Header file with definitions related to the I/O connections on the TI SmartRF06EB. More...

#include "dev/gpio.h"
#include "dev/nvic.h"

Macros
SmartRF LED configuration
LEDs on the SmartRF06 (EB and BB) are connected as follows: LED1 (Red) -> PC0 LED2 (Yellow) -> PC1 LED3 (Green) -> PC2 LED4 (Orange) -> PC3 LED1 shares the same pin with the USB pullup
#define	LEDS_YELLOW 2
	LED2 (Yellow) -> PC1.

#define	LEDS_GREEN 4
	LED3 (Green) -> PC2.

#define	LEDS_ORANGE 8
	LED4 (Orange) -> PC3.

#define	LEDS_CONF_ALL 15

#define	LEDS_RED 1
	LED1 (Red) -> PC0.

#define	PLATFORM_HAS_LEDS 1

USB configuration
The USB pullup is driven by PC0 and is shared with LED1
#define	USB_PULLUP_PORT GPIO_C_NUM

#define	USB_PULLUP_PIN 0

UART configuration
On the SmartRF06EB, the UART (XDS back channel) is connected to the following ports/pins RX: PA0 TX: PA1 CTS: PB0 (Can only be used with UART1) RTS: PD3 (Can only be used with UART1) We configure the port to use UART0. To use UART1, replace UART0_* with UART1_* below.
#define	UART0_RX_PORT GPIO_A_NUM

#define	UART0_RX_PIN 0

#define	UART0_TX_PORT GPIO_A_NUM

#define	UART0_TX_PIN 1

#define	UART1_CTS_PORT GPIO_B_NUM

#define	UART1_CTS_PIN 0

#define	UART1_RTS_PORT GPIO_D_NUM

#define	UART1_RTS_PIN 3

SmartRF Button configuration
Buttons on the SmartRF06 are connected as follows: BUTTON_SELECT -> PA3 BUTTON_LEFT -> PC4 BUTTON_RIGHT -> PC5 BUTTON_UP -> PC6 BUTTON_DOWN -> PC7
#define	BUTTON_SELECT_PORT GPIO_A_NUM
	BUTTON_SELECT -> PA3.

#define	BUTTON_SELECT_PIN 3

#define	BUTTON_SELECT_VECTOR NVIC_INT_GPIO_PORT_A

#define	BUTTON_LEFT_PORT GPIO_C_NUM
	BUTTON_LEFT -> PC4.

#define	BUTTON_LEFT_PIN 4

#define	BUTTON_LEFT_VECTOR NVIC_INT_GPIO_PORT_C

#define	BUTTON_RIGHT_PORT GPIO_C_NUM
	BUTTON_RIGHT -> PC5.

#define	BUTTON_RIGHT_PIN 5

#define	BUTTON_RIGHT_VECTOR NVIC_INT_GPIO_PORT_C

#define	BUTTON_UP_PORT GPIO_C_NUM
	BUTTON_UP -> PC6.

#define	BUTTON_UP_PIN 6

#define	BUTTON_UP_VECTOR NVIC_INT_GPIO_PORT_C

#define	BUTTON_DOWN_PORT GPIO_C_NUM
	BUTTON_DOWN -> PC7.

#define	BUTTON_DOWN_PIN 7

#define	BUTTON_DOWN_VECTOR NVIC_INT_GPIO_PORT_C

#define	PLATFORM_HAS_BUTTON 1

ADC configuration
These values configure which CC2538 pins and ADC channels to use for the ADC inputs. ADC inputs can only be on port A.
#define	ADC_ALS_PWR_PORT GPIO_A_NUM
	ALS power GPIO control port.

#define	ADC_ALS_PWR_PIN 7
	ALS power GPIO control pin.

#define	ADC_ALS_OUT_PIN 6
	ALS output ADC input pin on port A.

SPI configuration
These values configure which CC2538 pins to use for the SPI lines.
#define	SPI_CLK_PORT GPIO_A_NUM

#define	SPI_CLK_PIN 2

#define	SPI_MOSI_PORT GPIO_A_NUM

#define	SPI_MOSI_PIN 4

#define	SPI_MISO_PORT GPIO_A_NUM

#define	SPI_MISO_PIN 5

Device string used on startup
#define	BOARD_STRING "TI SmartRF06 + cc2538EM"

Detailed Description

Header file with definitions related to the I/O connections on the TI SmartRF06EB.

Note: Do not include this file directly. It gets included by contiki-conf after all relevant directives have been set.

Definition in file board.h.

Macros

Detailed Description